Can a basement have 2 sump pumps?

You could set both sump pumps at the bottom of your sump pit basin, but that would mean that both pumps would run at the same time. The more a pump turns on and off the shorter the life span. So, by installing the 2nd sump pump slightly higher, or on top of the primary pump, they won’t be working in tandem.

How much does it cost to install a second sump pump?

Sump Pump Installation Cost Estimate

Sump Pump Installation and Labor Cost Estimate
Average Cost	$1,200
Highest Cost	$3,000 – $3,800
Lowest Cost	$600 – $1,000

Why do I have 2 sump pumps?

The reason for 2 sump pumps per pit is to ensure you have a fail-safe in case the first one, or your home’s power fails. Now, if you have a whole-home generator, the battery backup can be replaced with a secondary Primary Sump Pump.

Do I need a second sump pump?

Depending on where you live and the height of your water table, you may need a second sump pump to keep your basement dry – especially during periods of heavy rain. This backup sump pump can be a lifesaver if your primary pump stops working or becomes overwhelmed.

How many sump pumps do I need?

Each Sump Pit should have 2 pumps, a Primary and a Backup (whether it be a battery backup, or in the case of a home-generator, a secondary Primary) Drain Tile needs to be sloped 1/8” per Linear Foot. Incorrectly installed Drain Tile and inadequate Sump Pumps and Pits will cause your basement to flood.

Do I need 2 sump pumps?

Can I install a sump pump myself?

If your sump pump is failing and you need to replace it, it’s a DIY job you can handle yourself. Note: Contact your local building code authorities if you’re digging a sump pit for a new sump pump installation. You may need a permit.

How many years does a sump pump last?

about 10 years
How Long Does A Sump Pump Last On Average? Like other appliances and equipment in your home, your sump pump won’t last forever. Averaging about 10 years, you might not notice your sump pump has malfunctioned until it has stopped working.

How does a sump pump work in a basement?

Usually, sump pumps are installed in specially constructed sump pits. Water flows into the sump pit through drains or by natural water migration through the soil. The sump pump’s job is to pump the water out of the pit and away from the building so the basement or crawlspace stays dry.

How to install a sump pump?

The first step to installing a sump pump is to find a location where the water collects.

Dig a hole six inches deeper and 10 inches wider than the sump. Place three inches of gravel in the bottom of the hole.

Stand in the sump,then pour more gravel around the sump leaving one or two inches at the top of the sump exposed.

Glue the male adapter to the PVC discharge pipe,then place into the female adapter on the pump.

Attach the pumps electrical cord to the discharge pipe using wire ties. Install a check valve on the open end of the discharge pipe.

Use pressurized fittings and 1 1/2 inch PVC to channel water from the pump and away from the house.

Install ‘J’ hooks to hang the PVC from the joists. Make a hole through the outside wall to run the PVC out.

Apply silicone sealant into the hole where the pipe comes out of the house.

Attach a 1 1/2 inch by three inch increaser on the end of the pipe to spread out the water flow.

Place gravel around the corrugated pipe to keep it in place. Plug in the pump. Place the cover over the sump.

What is a sump pump and how does it work?

A sump pump is a small pump installed in the lowest part of a basement or crawlspace. Its job is to help keep the area under the building dry and to prevent it from flood­ing. Usually, sump pumps are installed in specially constructed sump pits.

What is a basement pump system?

A sump pump is a pump that is installed in a basement or crawl space, just below the floor. They’re designed to collect water from the foundation soil and from a perimeter French drain, discharging the water outside of the house through a line of PVC pipe.