Why does my pool pump keep tripping the circuit breaker?

Your pool pump’s motor is kept away from the water. If this moisture gets through the pump motor coil, it may result in a short circuit and immediately trip its breaker. To address this kind of problem, open the outside cover of the motor and use a blower or a heat gun to speed up its drying process.

Why is my Hayward pool pump tripping breaker?

Pump Trips the Breaker If the breaker trips while the pump is running, the pump is likely drawing more amperage or voltage than the breaker rating. This could be caused by incorrect voltage or from clogged or restricted pipes, valves or impeller. It could also be just a bad breaker.

Does a pool pump need to be on a dedicated circuit?

You want a thicker extension cord, because a pool pump requires a good amount of electricity to run. Also, because the pump uses a lot of power, the outlet that you plug the extension cord into should be on what is called a “dedicated circuit”.

Do I need a GFCI breaker for pool pump?

-NEC requires GFCI protection for all pool pumps. A pool builder or electrician cannot install power to your pool pump per code without one. -Moisture from rain, sprinklers, or runoff causes GFCI breakers to trip as well. -Some breakers experience a lower rate of nuisance tripping than others.

How do you know if your pool pump is bad?

common pump problems and quick fixes

1. The Pool Pump is Making a Loud Screeching Noise or Sounds Like it’s Full of Rocks.
2. The Pool Pump is Leaking Water.
3. The Pool Pump Basket Does Not Fill with Water.
4. The Pool Pump is Making a Humming Noise and will not Start.
5. The Pool Pump is Sucking in Air.

What to do if breaker keeps tripping?

To reset a tripped circuit breaker, turn off the breaker by moving the switch or handle to the off position, and then turn it back on. For safety, it’s a good idea to stand back or to the side of the panel, just in case any sparks come from the breaker when it’s moved, or to wear safety goggles.

What is the average life of a pool pump?

between eight to 12 years
Well-maintained high-quality pool pumps can last between eight to 12 years. If you’ve missed out on many critical pool services, however, you can expect your pump to fail sooner. If your pump is more than half a decade old and it’s becoming more and more problematic, it’s best to get a new one.

Should my pool pump be on a GFCI breaker?

-NEC requires GFCI protection for all pool pumps. A pool builder or electrician cannot install power to your pool pump per code without one. -Moisture from rain, sprinklers, or runoff causes GFCI breakers to trip as well.

How many amps does a pool pump need?

5-8
If you need to know the electrical requirements for your inground pool, here is a list of common pool equipment and the approximate volts and amps required for each: Pool Pump: 240v, 10amps. Salt Water Chlorinator: 240v, approx 5-8 amps.

Does 240v pool pump need GFCI?

Only single phase 120-240-volt pool motors require GFCI protection. The replacement pump motor shall be provided with ground-fault circuit-interrupter protection.

How many amps does a pool pump draw?

Since it’s an aboveground pool pump it’s an uprated model and draws in the vicinity of 10 to 12 Amps at 120 volts. It might draw less depending on your plumbing.

What is the lifespan of a pool pump?

What causes a pool pump to trip a circuit breaker?

What Causes a Pool Pump to Trip a Circuit Breaker? Wiring. The pool pump receives electricity by way of power lines connected to the circuit breaker. Hot Wires. When two electrical wires touch, the power demand placed on the circuit breaker increases, tripping the breaker. Electrical Load. It’s possible for a circuit breaker to supply power to more than one device. Breaker Amperage.

What size breaker should I use for a pool pump?

One is so you can know what size breaker is needed at the electric box and the other so you know what size of wire to run to the pool’s pump. A typical above ground pool pump will require a 20-amp breaker and use #12 gauge wire to deliver the electricity.

Why does my pool pump keep tripping?

Your pool pump’s circuit breaker used to keep your pool pump running safely and accurately. But sometimes, your pool pump may end up tripping it, causing the breaker to fail and no power in your pool pump! It’s not only an irritating situation, but also something that may lead to danger.

Do swimming pool pumps require GFCI breakers?

The National Electric Code requires that all swimming pool pumps be connected to a GFCI breaker . As a residential electrical contractor wiring thousands of swimming pool pumps, we at Hawkins decided to explain some common issues that we find with these breakers.