Shakuhachi.net

Best place for relax your brain

What does the reload command do in Cisco?

0

What does the reload command do in Cisco?

The reload command halts the system. If the system is set to restart on error, it reboots itself. Use the reload command after configuration information is entered into a file and saved to the startup configuration.

How do I reset my Cisco port to default?

Resetting the Cisco IP switch to factory defaults

  1. Reset the switch to factory defaults: Erase the existing configuration: write erase. Reload the switch software: reload.
  2. Save the configuration: IP_switch-A-1# copy running-config startup-config.
  3. Reboot the switch and wait for the switch to reload: IP_switch-A-1# reload.

What is the command to restart a Cisco switch?

Using a pin, press and hold the Reset button on the switch for 15 to 20 seconds.

What is the difference between reload and restart?

Reload will tell the service to reload its configuration files, but keep the same process running. Restart tells it to shut down entirely, then restart. Generally speaking, restart will terminate the service in question and restart it; reload will only reload the configuration file.

How do I clear my interface configuration?

Steps

  1. Go to Network > Interfaces.
  2. Select the interface.
  3. Click ‘Delete’ and then click ‘Yes’ in the confirmation dialog to execute the deletion.

How do I set default interface in Cisco?

To initialize all FastEtehernet0/0 settings, type default interface FastEthernet0/0 in global configuration mode.

  1. R1#configure terminal.
  2. Enter configuration commands, one per line.
  3. R1(config)# default interface FastEthernet 0/0.
  4. Building configuration…
  5. Interface FastEthernet0/0 set to default configuration.

How long does it take for a switch to reload?

How Long Does It Take For A Switch To Reload? Even though force restarts are risky, sometimes they are necessary when the Switch operating system is unresponsive, rather than when it crashes. It should take no more than 20 seconds for the Switch to restart, and it is fairly easy to force it to do so.

How do you reload a router?

Steps to Reboot a Router and Modem

  1. Unplug the router and the modem.
  2. Wait at least 30 seconds.
  3. Plug in the modem.
  4. Wait at least 60 seconds.
  5. Plug in the router.
  6. Wait at least 2 minutes.
  7. When the router and modem restart, test to see if the problem went away.

How do I reboot my Cisco router?

First switch on your Cisco Router. Then, connect your PC or Laptop to the console port on your router with the console cable. After that, power on the router and wait 5 to 7 minutes for the router to finish booting.

What is a switch reload?

They all mean the same thing! On Cisco routers and switches the terminology is ” reload ” to “restart” the device. You tend to hear the term “reboot” from us older guys.

What is the Cisco “reload” command used for?

The Cisco “reload” command is used on almost all IOS Cisco networking devices (routers, switches etc) to restart (or reboot) the appliance. This command might seem very basic but it has some interesting practical applications that we will see later in this article.

What is the use of the “reload command” in Linux?

This command might seem very basic but it has some interesting practical applications that we will see later in this article. As we have said above, the basic usage of this command is to reload the IOS operating system of the router or switch.

What is the output of showinterfacesdcc on a Cisco 12000 router?

The following is sample output from the showinterfacesdcc command on a Cisco 12000 series router for POS interface 1/1/0 (which is the interface for port 0 of the SPA in subslot 1 of the SIP in chassis slot 1): The table below describes the significant fields shown in these displays. Field Description SDCCx/y/z is up, line protocol is up

What is the show interfaces command in Cisco routers?

This command was integrated in Cisco IOS Release 15.1 (50)SY. The show interfaces command displays statistics for the network interfaces. The resulting output varies, depending on the network for which an interface has been configured. The resulting display on the Cisco 7200 series routers shows the interface processors in slot order.