How do I provision a Cisco SPA122?

Procedure

1. Using a LAN/Ethernet cable, connect the computer to the yellow Ethernet (LAN) port of the SPA122.
2. Open Internet Explorer browser (IE is required to ensure the adapter’s configuration page displays properly).
3. Log in: admin / (administrator password)
4. Click Voice > Provisioning.
5. Click Submit.

How do I access Spa 112?

How to access the web configuration utility on the Cisco SPA112

1. Open a web browser and enter the IP address of the phone adapter in the address bar, then press Enter.
2. Enter the username of the device in the Username field.
3. Enter the password of the device in the Password field.

How do I find the IP address of my Cisco SPA122?

At the voice prompt menu, enter 110 #. The phone will read back the IP address of the base, which can be entered into a browser to access the configuration. At the voice prompt menu, enter 210 #. The phone will read back the IP address of the base, which can be entered into a browser to access the configuration.

What does a Cisco ATA do?

Your analog telephone adapter (ATA) allows you to connect an analog device, such as an analog phone or fax machine, to your network. The connected device can then function like the IP phones in your network.

How do I reset my SPA122?

The Built-in IVR System This is probably the most convenient way to reset and restore the SPA112 defaults: Plug your analog telephone into one of the rear-panel telephone RJ-11 jacks. Then, dial the following IVR code: 73738 followed by the # key. TIP: RESET spelled out on the telephone keypad = 73738.

How do I connect my ATA to my router?

Use the Ethernet cable that came with your ATA to connect the LAN or Internet port on your ATA to an available LAN port on your router. Then use a standard RJ11 telephone cable to plug your touch-tone analog phone into the PHONE 1 port of your ATA. power source. It will take about two to three minutes to fully boot.

How do I set up ATA 191?

Connect the ATA power cable to the DC 5V POWER port on the ATA, and plug the power cable into your power source….Before you begin

1. Ethernet cable to connect to your network.
2. Analog phone or fax machine to connect to your ATA.
3. Phone cable to connect your phone.
4. Uninterruptible power supply (UPS) to provide backup power.

How do I log into network configuration utility?

To open the web-based configuration utility: Open a Web browser. Enter the IP address of the WAP device that you are configuring in the address bar on the browser, and then press Enter. The Login page opens.

How do I reset my Cisco SPA122?

RESET — Press the Reset button to restart the SPA122 device. To restore it to factory default settings, hold the button for 20 seconds.

How do I configure ATA 192?

Connect the network cable to your network and to the NETWORK port on the ATA….Install Your New ATA 191 and 192

1. Ethernet cable to connect to your network.
2. Analog phone or fax machine to connect to your ATA.
3. Phone cable to connect your phone.
4. Uninterruptible power supply (UPS) to provide backup power.

How do I Activate my Cisco spa122 ATA adapter?

Lift the handset and follow the voice instructions sPa122 ata, contact 8×8 to enter the activation code. Page 2 InstallatIon GuIde Cisco SPA122 ATA Indicator Lights The status of your adapter can be determined by looking at the indicator lights on the side panel.

How to configure Cisco spa-112/122 VoIP SIP adapter?

Cisco SPA-112/122 VoIP SIP adapter configuration manual 1 Before configuration you need to have an active account with us. 2 If you don’t have an adapter, you may purchase it here: Buy Cisco SPA-112 phone adapter 3 Connect your device’s power and Ethernet cables. 4 Wait 60 seconds after plugging your SPA112/SPA122 in.

How do I troubleshoot a Cisco spa122 network problem?

Ensure that the cable in the INTERNET (WAN) port is securely connected to the device that provides your Internet access, such as your modem or ADSL line. On the Cisco SPA122, check the cable connection for the ETHERNET (LAN) port.

What is provisioning guide for Cisco spa100 and spa200 series analog telephone adapters?

Provisioning Guide for Cisco SPA100 and SPA200 Series Analog Telephone Adapters 92 6 Number of successive ICMP errors allowed when transmitting RTP packets to the peer before the ATA terminates the call.